=********************************************************Systems HELP*********************************************************= =-----------------------------------------------------------------------------------------------------------------------------= = System Address = 00 F/W Version : 1.49 = = Azz : All Commands start by Prefix System Address zz, if [01-99] = =-----------------------------------------------------------------------------------------------------------------------------= = H : Help = = STA : Show Global System Status = = SET RST : Reset to Factory Defaults = = SET RBT : System Reset to Reboot = = SET LAN RBT : SET LAN MCU Reset to Reboot = = SET ADDR xx : Set System Address to xx {xx=[00~99](00=Single)} = = SET LCD ON Tx : Set LCD Remain On Time{x=[0~3](0=Always ON,1=15,2=30,3=60Sec)} = = SET KEY LOCK ON/OFF : Set Key Lock On/Off = = SET FAN SPEED x : Set Fan Speed{x=[0~6]} = = GET ADDR : Get System Address = = GET STA : Get System Status = = GET DEV TEMP : Get Device Temperature = = GET INx SIG STA : Get Input x Signal Status{x=[0~16](0=ALL)} = = GET INx VID FMT INF : Get Input x Video Format Info{x=[0~16](0=ALL)} = = GET LCD ON T : Get LCD Remain On Time = = GET KEY LOCK : Get Key Lock Status = =-----------------------------------------------------------------------------------------------------------------------------= =Output Setup Commands: Output Num[0~16] = = SET OUTx VS INy : Set Output x To Input y{x=[0~16](0=ALL), y=[1~16]} = = SET OUTx VFMTy : Set Output x Video Timing Format{x=[0-16](0=ALL), y=[1-20]} = = : {(1=480P60Hz,2=720p60Hz,3=1080p60Hz,4=1920X1200RB60Hz, = = : 5=4K30Hz,6=4K60HzY420,7=4K60Hz,8=Self-Adapt) = = : 9=640X480,10=1024X768,11=1280X768,12=1280X800) = = : 13=1280X960,14=1280X1024,15=1360X768,16=1366X768) = = : 17=1400X1050,18=1600X1200,19=1680X1050,20=4096X2160)} = = SET OUTx TP VIDEOy : Set HDBT Output x VIDEO Mode y = = {x=[0~16](0=ALL), y=[2,5](2=4K->2K,5=ICT Mode)} = = SET OUTx TP POEy : Set HDBT Output x Power Mode{x=[0-16](0-ALL),y=[0-1](0-Auto,1-EN)} = = SET OUTx EXA EN/DIS : Set Ex-Audio Output x Enable/Disable{x=[0~16](0=ALL)} = = SET OUTx EXADL PHy : Set Ex-Audio Delay{x=[0~16](0=ALL), y=[0~7](0=Bypass,1~7=90,180,270,360,450,540,630MS)} = = SET EXAMX MODEx : Set Ex-Audio Matrix Mode{x=[0~2](0=Bind To Output,1=Bind To Input,2=Matrix} = = SET OUTx AS INy : Set Ex-Audio Output x To Input y{x=[0~16](0=ALL), y=[1~16]} = = SET OUTx EXAUD LEVy : Set Output x EQ-Audio Volume Levely{x=[1-16],y=[0~20]} = = SET OUTx HP SGM EN/DIS : Set HDMI Output x Signal Generator Enable/Disable{x=[0-16](0=ALL)} = = SET OUTx TP SGM EN/DIS : Set HDBT Output x Signal Generator Enable/Disable{x=[0~16](0=ALL)} = = SET OUTx HP STREAM ON/OFF : Set MIRROR Output x Stream ON/OFF Status{x=[0/Odd Num](0=ALL)} = = SET OUTx TP STREAM ON/OFF : Set MAIN Output x Stream ON/OFF Status{x=[0~16](0=ALL)} = = SET OUTx HP CEC x1x2.yy.mm.pp : Set CEC Param To HDMI Output Port = = : x1x2=[Logical Address,x1-Initiator,x2-Destination],yy=[Opcode], = = : mm=[Data Param Length[0-14],Length EX x1x2&yy],pp=[Data Param] = = : Example: [SET OUT1 HP CEC 50.84.3.10.00.05] = = SET OUTx TP CEC x1x2.yy.mm.pp : Set CEC Param To HDBT Output Port = = : x1x2=[Logical Address,x1-Initiator,x2-Destination],yy=[Opcode], = = : mm=[Data Param Length[0-14],Length EX x1x2&yy],pp=[Data Param] = = : Example: [SET OUT1 TP CEC 50.84.3.10.00.05] = = GET OUTx VS : Get Output x Video Route{x=[0~16](0=ALL)} = = GET OUTx VFMT : Get Output x Video Timing Format Status{x=[0-16](0=ALL)} = = GET OUTx HP VIDEO : Get HDMI Output x Video Mode{x=[0~16](0=ALL)} = = GET OUTx TP VIDEO : Get HDBT Output x Video Mode{x=[0~16](0=ALL)} = = GET OUTx TP POE : Get HDBT Output x Power Mode{x=[0-16]} = = GET OUTx EXA : Get Ex-Audio Output Enable/Disable Status{x=[0~16](0=ALL)} = = GET OUTx EXADL PH : Get Ex-Audio Output Delay Status{x=[0~16](0=ALL)} = = GET EXAMX MODE : Get Ex-Audio Matrix Mode = = GET OUTx AS IN : Get Output x Ex-Audio Route{x=[0~16](0=ALL)} = = GET OUTx EXAUD LEV : Get Output x EQ-Audio Volume Level{x=[0-16](0=all)} = = GET OUTx HP SGM : Get HDMI Output x Signal Generator Enable/Disable Status{x=[0-16](0=ALL)} = = GET OUTx TP SGM : Get HDBT Output x Signal Generator Enable/Disable Status{x=[0~16](0=ALL)} = = GET OUTx HP STREAM : Get HDMI Output x Stream ON/OFF Status{x=[0-16](0=ALL)} = = GET OUTx TP STREAM : Get HDBT Output x Stream ON/OFF Status{x=[0~16](0=ALL)} = = GET OUTx HP EDID DATA : Get HDMI Output x EDID DATA{x=[1-16]} = = GET OUTx TP EDID DATA : Get HDBT Output x EDID DATA{x=[1~16]} = =-----------------------------------------------------------------------------------------------------------------------------= =Input Setup Commands: = = SET INx EDID y : Set Input x EDID{x=[0~16](0=ALL), y=[0~32]} = = 0:1080P_2CH 1:1080P_6CH 2:1080P_8CH 3:1080P_3D_2CH = = 4:1080P_3D_6CH 5:1080P_3D_8CH 6:4K30HZ_3D_2CH 7:4K30HZ_3D_6CH = = 8:4K30HZ_3D_8CH 9:4K60HzY420_3D_2CH 10:4K60HzY420_3D_6CH 11:4K60HzY420_3D_8CH = = 12:4K60HZ_3D_2CH 13:4K60HZ_3D_6CH 14:4K60HZ_3D_8CH 15:1080P_2CH_HDR = = 16:1080P_6CH_HDR 17:1080P_8CH_HDR 18:1080P_3D_2CH_HDR 19:1080P_3D_6CH_HDR = = 20:1080P_3D_8CH_HDR 21:4K30HZ_3D_2CH_HDR 22:4K30HZ_3D_6CH_HDR 23:4K30HZ_3D_8CH_HDR = = 24:4K60HzY420_3D_2CH_HDR 25:4K60HzY420_3D_6CH_HDR 26:4K60HzY420_3D_8CH_HDR = = 27:4K60HZ_3D_2CH_HDR 28:4K60HZ_3D_6CH_HDR 29:4K60HZ_3D_8CH_HDR = = 30:USER1_EDID 31:USER2_EDID 32:USER3_EDID = = SET INx EDID CY OUTy HP : Copy HDMI Output y EDID To Input x(USER1 BUF){x=[0~16](0=ALL), y=[Odd Num]} = = SET INx EDID CY OUTy TP : Copy HDBT Output y EDID To Input x(USER1 BUF){x=[0~16](0=ALL), y=[1~16]} = = SET INx EDID Uy DATAz : Write EDID To User y Buffer of Input x{x=[0~16](0=ALL), y=[1~3],z=[EDID Data]} = = SET INx TMDS ON/OFF : Set Inputx Port Power Status ON/OFF{x=[0~16](0=ALL) = = GET INx EDID : Get Input x EDID Index{x=[0~16](0=ALL)} = = GET INx EDID y DATA : Get Input x EDID y Data{x=[1~16],y=[0~32]} = = GET INx TMDS : Get Inputx Port Power Status{x=[0~16](0=ALL) = =-----------------------------------------------------------------------------------------------------------------------------= =Network Setup Command: ( xxx=[000-255], zzzz=[0001~9999] = = SET RIP xxx.xxx.xxx.xxx : Set Route IP Address to xxx.xxx.xxx.xxx = = SET HIP xxx.xxx.xxx.xxx : Set Host IP Address to xxx.xxx.xxx.xxx = = SET NMK xxx.xxx.xxx.xxx : Set Net Mask to xxx.xxx.xxx.xxx = = SET TIP zzzz : Set TCP/IP Port to zzzz = = SET DHCP y : Set DHCP {y=[0~1](0=Dis,1=Enable)} = = GET RIP : Get Route IP Address = = GET HIP : Get Host IP Address = = GET NMK : Get Net Mask = = GET TIP : Get TCP/IP Port = = GET DHCP : Get DHCP Status = = GET MAC : Get MAC Address = =-----------------------------------------------------------------------------------------------------------------------------= =IR Route Setup Command: = = SET IRC OUTy MUX zz : zz={x1.x2.x3.x4.x5.x6.x7.x8.x9.x10.x11.x12.x13.x14.x15.x16} = = : Set IR Route Channel Switch{x1~x16=[0,1](0=Disable,1=Enable),y=[0~4]} = = SET IRT OUTx IS INy : Set Output x IR Route{x=[0~16](0=all),y=[1~16]} = = SET LIR EXT SW zz : zz={x1.x2.x3.x4.x5.x6.x7.x8.x9.x10.x11.x12.x13.x14.x15.x16} = = : Set Local IR Extender Switch{x1~x16=[0,1](0=Disable,1=Enable)} = = SET CIR EXT SW zz : zz={x1.x2.x3.x4.x5.x6.x7.x8.x9.x10.x11.x12.x13.x14.x15.x16} = = : Set Callback IR Extender Switch{x1~x16=[0,1](0=Disable,1=Enable)} = = GET IRC OUTy MUX : Get IR Route Channel Switch Status{x=[0~4](0=all)} = = GET IRT OUTx IS : Get Output x IR Route{x=[0~16](0=all)} = = GET LIR EXT SW : Get Local IR Extender Switch Status = = GET CIR EXT SW : Get Callback IR Extender Switch Status = =-----------------------------------------------------------------------------------------------------------------------------= =RS232 Route Setup Command: = = SET RS CHy MUX zz : zz={x1.x2.x3.x4.x5.x6.x7.x8.x9.x10.x11.x12.x13.x14.x15.x16} = = : Set the RS232 MUX{y=[1],x1~x16=[0-1](0=Disable,1=Enable)} = = SET RS PTH OUTx LENy BRz : Set RS232 Control Pass Through to Outputx = = {x=[0-16](0=ALL),y=[1~800],z=[0~5](0=9600,1=14400,2=19200,3=38400,4=57600,5=115200)} = = GET RS CHx MUX : Get the RS232 MUX Status{x=[1]} = =-----------------------------------------------------------------------------------------------------------------------------= =IR Code Setup Command: = = SET IR SYS xx.yy : Set IR Custom Code{xx=[00-FFH],yy=[00-FFH]} = = SET IR OUTx INy CODE mm.nn : {x=[1~16],y=[1~16],mm=[00~FFH,Output],nn=[00~FFH,Input]} = = GET IR SYS : Get IR Custom Code = = GET IR OUTx INy CODE : Get IR Data Code{x=[1~16],y=[1~16]} = =-----------------------------------------------------------------------------------------------------------------------------= =*****************************************************************************************************************************= ===============================================================================================================================